: Public <<DataType>> Class
Created: 9/01/2015 2:43:45 PM
Modified: 12/05/2015 2:11:58 PM
Project:
Advanced:
Metadata applicable to the whole timeseries.
Attribute
Public TM_Period
  temporalExtent
Details:
sequenceNumber=1
Notes: The extent of the temporal domain of the timeseries. As the domain of the timeseries is temporal, the temporalExtent is a time period defining the start and end of its temporal domain (i.e. the start and end of the timeseries). Note that this often the same as the phenomenon time as specified in the OM_Observation; it is still useful here for timeseries that are described separately from an OM_Observation header.
Public TM_Position
  baseTime
Details:
sequenceNumber=2
Notes: Timeseries that are regularly spaced, such as those that are generated from automatic sensors, can be represented without specifying the individual time instant for each point. The #lt;i#gt;spacing#lt;/i#gt; property of the time series is used to specify the time between points. This is then used as the spacing for each point encountered, starting from the time set by #lt;i#gt;baseTime.#lt;/i#gt;
Public TM_Period
  intendedObservationSpacing
Details:
sequenceNumber=5
Notes: The extent of the temporal domain of the timeseries. As the domain of the timeseries is temporal, the temporalExtent is a time period defining the start and end of its temporal domain (i.e. the start and end of the timeseries). Note that this often the same as the phenomenon time as specified in the OM_Observation; it is still useful here for timeseries that are described separately from an OM_Observation header.
Public Boolean
  cumulative
Details:
sequenceNumber=29
Notes: This boolean property indicates whether the series is  sequentially increasing and accumulates over time; i.e. each value is added to the last so the value represents the total of a value since accumulation began.
Public TM_Period
  accumulationAnchorTime
Details:
sequenceNumber=30
Notes: Defines the time at which accumulation begins. e.g. 9am.#lt;br /#gt;#lt;/p#gt;#lt;p#gt;NOTE - SHOULD THIS BE TM INSTANT?#lt;br /#gt;#lt;/p#gt;
Public TM_PeriodDuration
  accumulationIntervalLength
Details:
sequenceNumber=40
Notes: Defines the length of time over which accumulation is recorded e.g. 24 hours
Public TM_Position
  startAnchorPoint
Details:
sequenceNumber=50
Notes: StartAnchorPoint specifies a ‘ghost’ point to allow the first value of the timeseries to be interpolated correctly.
Public TM_Position
  endAnchorPoint
Details:
sequenceNumber=60
Notes: EndAnchorPoint specifies a ‘ghost’ point to allow the last value of the timeseries to be interpolated correctly.
Public TM_PeriodDuration
  spacing
Details:
sequenceNumber=3
Notes: The time between points in a regularly spaced timeseries.
Public StatusCode
  status
Details:
sequenceNumber=20
Notes: Indicates the statues of the observation. E.g. unreleased, verified etc. 
Public SampledMediumCode
  sampledMedium
Details:
sequenceNumber=40
Notes: Indicates the medium that was sampled. E.g. water, air, etc.
Public TM_PeriodDuration
  maxGapPeriod
Details:
sequenceNumber=70
Notes: When any analysis is run over a timeseries it is important to know if it is possible to interpolate between any two adjoining points. If the join period between two adjoining points is greater than the maxGapPeriod then the series should not be interpolated between these adjoining points.
Public NamedValue
  parameter
Details:
sequenceNumber=100
Notes: This is a named value extension point that allows extra metadata to be added at the timeseries level. The parameters here are soft-typed (i.e. this standard does not define the properties semantics). Commonly used parameters here would be future candidates for definition within later versions or community extensions. 
Element Source Role Target Role
«DataType» CommentBlock
Class   		Name:  
  		Name: commentBlock
 
Details:
 
Element Source Role Target Role
«FeatureType» TimeseriesTVP
Class   		Name:  
  		Name: metadata
Metadata about the timeseries
Details:
 
Tag Value
isCollection false
Details:
Values: true | false
Default: false
Description: Identifies the data type as an object collection.
noPropertyType false
Details:
Values: false
Default: false
Description: Surpress creation of a standard property type that supports inline encoding (applies to ISO 19136:2007 encoding rule). Always set to false in INSPIRE.
xsdEncodingRule iso19136_2007
Details:
Values: iso19136_2007 | iso19139_2007 | iso19136_2007_INSPIRE_Extensions
Default: iso19136_2007
Description: XML Schema encoding rule to apply
Constraint Type Status
temporalExtent = domainExtent (renamed) Invariant Approved
Details:
 
Object Type Connection Direction Notes
«DataType» CategoricaTimeserieslMetadata Class Realization To  
«DataType» MeasurementTimeseriesMetadata Class Realization To  
«DataType» TimeseriesMetadata Class Realization To